What's New in IQCreator® Version 8.10.0
1. Added LTE FDD (Uplink and Downlink) Modulation.
2. The 302xC Series packager now supports files upto 512Msamples in length.
3. The 39xx Series packager now supports sampling rates up to 2MHz and
   bandwidths up to 1MHz.

The following problems have been fixed in Version 8.10.0:
1. The WiMAX OFDM UL subchannelization has been fixed.

What's New in IQCreator® Version 8.9.0.
1. A new packager (302xC series) has been created for the new “C” series PXI modules. 
2. WiMAX OFDM and OFDMA now support a bandwidth of 28MHz.
3. 1xEvdo and 1xEvdo rev A now support positive channel gains.
4. AWGN has been updated so that noise bandwidths of 100 MHz can be created  
   (to support the  “C “ series PXI modules).

The following problems have been fixed in Version 8.9.0: 
1. User files with a sample rate between 33MHz and 44MHz can now be packaged using 
   the 3020 packager directly. Prior to this release files with this sample rate could 
   only be packaged using the user modulation scheme.
2. The WiMAX OFDMA modulation dll now applies data subchannel rotation correctly 
   when generating multiple UL pusc zones.
3. The WiMAX OFDMA modulation dll now lets the user use all subchannels when the
   Use All Subchannels Indicator is on.


The following problems have been fixed in Version 8.8.0:
1. IQCreator now allows files packaged using the "Aeroflex 3410 V4.09+ Series"
   packager to be downloaded to Aeroflex 3410 Series Instruments.
2. The "Aeroflex 3410 v4.09+ Series" packager now allows three general markers
   to be defined.

What's New in IQCreator® Version 8.7.0.

1. 3Gpp TDD-LCR modulation support
2. A new 3410 packager has been included (3410 v4.09+) that allows marker 1 to
   be setup as a general marker. Requires the 341x signal generator to have
   firmware version 4.09 or later to be installed.

The following problems have been fixed in Version 8.7.0:
1. IQCreator no longer crashes when packaging a file of 65536 samples and an
   over sampling factor of 4.
2. The sample rate is no longer limited to 100 MHz in user modulation.
3. The auto calculating of the sample rate in tones has been modified to work
   with higher sample rates.
4. The marker repeat length in tones will now be calculated correctly. The
   repeat length had previously been calculated incorrectly with certain file
   lengths which caused errors.
5. The markers from aiq files with a rise/fall profile of "none" can now be read
   into user modulation.
6. A problem that prevented certain delay lengths in multi-carrier from
   generating has now been fixed.
7. The data sources in TD-SCDMA are no longer reset after each frame meaning
   several frames can be generated carrying different data.

What's New in IQCreator® Version 8.6.0.

The following functionality has been added betweeen Version 8.5.0 and 8.6.0:
1. 1xEV-DO Rev A downlink support
2. A 3920 packager dll is now included with IQCreator.  

The following problems have been fixed in Version 8.6.0:
1. 3410 ALC bandwidth is now set to narrow for all modulation schemes. This
   should improve EVM.
2. MOD ID for 1xEVDO Rev A and Modified user files has been corrected so that
   the files can be downloaded onto a 3410.
3. WMAN OFDM IQC files now correctly store the preamble state.
4. All available WMAN OFDM Data Sources can now be selected from the list
   control's combobox.
5. TD-SCDMA Midamble gain adjusted so that it is transmitted at the same power
   as the data.
6. Multicarrier now uses the rms values in the aiq file to ensure output levels
   are correct.

The following functionality has been added betweeen Version 8.4.0 and 8.5.0:
1. Support for 3GPP release 6. 
	a. Enhanced data channels for case 2 and 3 have been added to the uplink.
	b. E-AGCH, E-RGCH and E-HICH channels have been added to the downlink.

The following problems have been fixed in Version 8.5.0:
1. Plots of zero only data now scale correctly.
2. User created aiq files (unencrypted) are now handled correctly.
3. Unhandled exception fixed when user data source file is not found in TDMA
   systems.
 
The follwing two problems were fixed in Version 8.4.0:
1. Files can now be loaded properly in User Modulation.
2. Multicarrier IQC files saved with Version 8.2.0 can now be loaded again
   without error.

The following functionality was added betweeen Version 8.2.0 and 8.3.0:

1. Support is now provided for 1xEVDO revision A (Uplink).
2. Support is now provided in WiMAX OFDMA for FUSC Zones in the Downlink and AMC
   in Downlink and Uplink.
3. A new modulation type UDSK (User Defined Shift Keying)has been added. This
   modulation type allows the user to define the constellation.
4. The Multicarrier DLL now has the ability for the user to set the oversampling
   factor explicitly and calculate the final sample rate of combined AIQ files.
5. User modulation now supports AIQ files. This will allow the user to view
   existing AIQ files, modify markers and repackage for different hardware.